SkyIPCam1500W Wireless N Night Vision Network Camera Model # AICN1500W User’s Manual Ver. 1.0
-9-Step 4 Click Finish when installation finishes.
-10-3.2 Configuring the Camera Step 1 Go to Start > (All) Programs > Airlink101 SkyIPCam UltraView > SkyIPCam Utiliy Step 2 Click on Se
-11-Step 3 When you are prompted for the user name and password, enter “admin” for both User name and Password, and click OK.
-12-Step 5 You may change the default Camera Name and enter a name for the Location if you like. Then enter “admin” for both Admin Password and Conf
-13- Step 7 If you would like to set up email alerts that you can receive in the future, enter your email information here. You can get this inform
-14-Step 9 Confirm your settings at this page. If everything is correct, click Apply to save the settings, then the camera will restart in 50 second
-15-3.3 Viewing Images Method A > Access Camera from SkyIPCam Utility Step 1A Open Airlink101 SkyIPCam Utility, select the camera you wish to co
-16-Step 3 Enter administrator’s user name and password of the camera, then click OK. The default user name and password are both “admin” if you did
-17-Step 5 Click on Run, then you will be able to view the image. Note If you are using Mozilla Firefox or Safari a
-18-CHAPTER 4 CONFIGURATION 4.1 Using the Web Configuration You can access and manage the camera through the Web browser and the provided software a
-1-CHAPTER 1 ... 2 INTRODUCTION TO YOUR
-19-Basic >> Date & Time Date & Time - TimeZone: Select the proper time zone for the region from the pull-down menu. - Synchroniz
-20-Basic >> User Administrator You can use this option to change administrator’s password for your camera. General User - User Name: E
-21-4.3 Network Settings The Network menu contains three sub-menus that provide the network settings for the camera, such as the IP Setting, DDNS Set
-22-Primary/ Secondary DNS DNS (Domain Name System) translates domain names into IP addresses. Enter the Primary DNS and Secondary DNS that are provi
-23-Network >> IP Filter The IP Filter setting allows the administrator of the camera to limit the users within a certain range of IP addresse
-24-Network >> Wireless Setting The camera supports WLAN while you use the wireless network. Select the Enable option to enable this feature.
-25- - Encryption: Select the WEP option to enable the data encryption feature to secure the camera within the wireless network. - Format:
-26-Network >> Wireless >> WPS Setting The camera supports WPS (WiFi Protected Setup™) feature that allows your camera to connect to the
-27-4.4 Setting up Video & Audio The Video & Audio menu contains three sub-menus that provide the video and audio settings for the camera.
-28-Video & Audio >> Video MJPEG - Video Resolution: Select the desired video resolution from the three formats: VGA, QVGA and QQVGA.
-2-CHAPTER 1 INTRODUCTION TO YOUR CAMERA 1.1 Checking the Package Contents Check the items contained in the package carefully. You should have the f
-29-4.5 Event Server Configuration The Event Server menu contains two sub-menus that allow you to upload images to FTP, and send emails that include
-30-Event Server Setting >> Email Email - SMTP Server Address: Enter the mail server address. For example, mymail.com. - Sender Email Add
-31-4.6 Motion Detect *This function can only be configured in Windows Internet Explorer. The Motion Detect menu contains the command and option tha
-32-4.7 Event Configuration The Event Config menu contains five sub-menus that provide the commands to configure event profiles. Event Configuration
-33-Event Configuration >> Arrange Schedule Profile This sub-menu displays the scheduled profile(s). To customize the profile, click Add and th
-34-Event Configuration >> Motion Detection Trigger Select the Enable option to enable the motion detection trigger function of the camera, so
-35-4.8 Tools The Tools menu provides the commands that allow you to restart or reset the camera. You can also backup and restore your configuration,
-36-4.9 Information The Information menu displays the current configuration and events log of the camera. Device Info Display the Basic, Video &
-37-CHAPTER 5 USING SKYIPCAM ULTRAVIEW 5.1 Starting the Program To start UltraView Pro, click Start Æ (All) Programs Æ Airlink101 SkyIPCam UltraVie
-38-5.2 Main Window and Item Feature When you start and login to UltraView, the Main window will display as below: The Main window provides you wi
-3- Rear View E
-39-Z Camera View Mode buttons in this area allow you to switch the camera view mode. Button Function Display the connected camera(s) in single came
-40-number (1~8) from the Go button. Navigation Buttons (Left/Right/Up/Down/Home). If the connected camera features pan/tilt functions, the Navigati
-41-5.3 Accessing the Camera Before you can access the camera, you have to add the camera to the system. Adding a Camera 1. Click the button a
-42-3. Click Device Search to search the camera(s) within your network. 4. When search is finished, select the camera and click Add.
-43-5. The information of the camera will be displayed on the window. When completed, click Preview and then click Save to return to the Device Sett
-44-6. Close the Device Setting window and return to the Main window. The image of the camera will be displayed. TIP When you add the cam
-45-7. Click on the button Motion detection area to enable and set up the motion detection feature of the camera. A new window pops up with setting
-46- Editing / Deleting a Camera Since you have added camera(s) to the system, you can select one to edit or remove. 1. On the Device Setting wind
-47- Viewing Image of the Camera Since you have added camera(s) to the system, the image of the selected camera(s) will be displayed on the Live Vi
-48-5.4 Recording / Playing Video Enabling / Disabling Recording Press Preview to activate the settings. While you are adding/editing the camera
-4-1.3 Features and Benefits Audio Capability The built-in microphone allows you to capture and monitor sounds and voices. Day & Night Sur
-49- Configuring the Recording Settings The default directory for saving the recorded video files is “C:\”. You can change the target folder for sa
-50- Setting up Schedule for Recording The system features the schedule recording so that you can set up the schedule to record as you need. Click
-51- Playback the Recording Files NOTE Divx/Xvid codec is required for the system to play the video files. If the video clips cannot be displayed
-52-5.5 Configuring the eMap View Setting Click the button and select View Setting to configure the camera view setting of eMap mode. eMap refers
-53-3. Click Browse to select a Picture File from your computer. The selected picture will be displayed in the Preview window. Click Save after you
-54- 5. When completed, click Save. Click Back to go back to the Main window. 6. To view from eMap: a. Click the button and select eMap View.
-55-b. Select the map from the eMap Name list. c. Click the camera icon, the camera window will then pop up to display the image of that location
-56-7. To view Camera Status: Click the button and select Camera Status. It shows the camera status as below. Editing / Deleting the eMap 1
-57-5.6 Configuring the System 1. User management: Click the button and select Account to change the administrator password for the UltraView sof
-58-2. To change the System Language: Click the button and select language to change the displayed system language. In the Language screen, select
-5- CHAPTER 2 HARDWARE INSTALLATION 2.1 Installing the Wall Mount Kit The camera comes with a camera stand, which uses a swivel ball screw head to
-59-3. To check the version number: Click the button and select Version to display UltraView software version number.
-60-4. System Setting: Click the button and select System Setting to set the Auto Scan time interval.
-61-5.7 Event Configuration Setting up Event Server Click the button and select Event Server to configure the SMTP server, so that you can send
-62- Sending Email Notification Click the button and select Address Book to assign the user to the Address Book of the camera. The user will recei
-63- Configuring Event Trigger Click the button and select Event Trigger to configure the trigger out function of the camera. 1. On the Event
-64-5.8 Terminating Operation When you have finished operating, click the button and select Logout to log out the system or Close to exit the progr
-65-Appendix A.1 Specification Image Sensor Sensor 1/4” color CMOS Resolution 640x480 Video Compression MJPEG Video resolution VGA/QVGA/QQ
-66-A.2 Glossary of Terms NUMBERS 10BASE-T 10BASE-T is Ethernet over UTP Category III, IV, or V unshielded twisted-pair media. 100BASE-TX The two-pa
-67-distributed company and operates the company’s mission-critical applications. Ethernet The most popular LAN communication technology. There are a
-68-J JAVA Java is a programming language that is specially designed for writing programs that can be safely downloaded to your computer through the
-6- If you use a wireless network in your application environment, you need to attach the included external antenna to the camera. When the camera is
-69-Detection (CSMA/CD), implemented as token-ring, ARCNET, FDDI, or Ethernet. The Router Information Protocol (RIP),a part of the Transmission Contr
-70-common carrier telecommunication techniques. WEP WEP is widely used as the basic security protocol in Wi-Fi networks, which secures data transmis
-71- Technical Support E-mail: [email protected] Toll Free: 1-888-746-3238 Web Site: www.airlink101.com
-7-CHAPTER 3 SOFTWARE INSTALLATION 3.1 Installing SkyIPCam Utility and UltraView Step 1 Insert the provided CD into your computer’s CD ROM drive.
-8-Windows 7 and Vista users: an AutoPlay window pops up on screen, please make sure you give permission to run the setup program by clicking Autorun
Comments to this Manuals